Equipment
Nissei ASB 70 DPH
Nissei ASB 70 DPH
.jpg/:/rs=w:388,h:517.3333333333334,cg:true,m/cr=w:388,h:517.3333333333334)
Serial #349A61206 2012 -Version 4 480 Volts - 60 Hz. (made in Japan) Blow type B - Including: Leveling pads.
Dryer: Novatec mode IMPC-220 - dew-point - 40' F' with hopper and stand
Take out: PETPOINT Automation built in 2023 model MAS04-01 serial #23/2023
Price:
Machine: $99,000.00
Dryer & Hopper: $5,000
Take Out: $15,000
FOB Gainesville, GA
Certification List Update:
A) Hydraulic tank: clean, filter, magnets, and flush.
B) V2 pump unit: new seal kit, bearing, and grease up couplings.
C) Low-pressure air: no air leaks, all Cushing working, replaced 8 mufflers, and will install a new seal kit for the stretch cylinder.
D) Barrel heaters: replaced 2, and thermocouple holders replaced 3 missing pins.
E) New paint inside and out.
F) Safety cage new Lexan.
G) Hydraulic hoses, replacing 14 of them, and 8 have been replaced.
H) Injection unit IU 35 with new 64mm long screw, torpedo assembly, and holding ring. On the injection cylinder, we have replaced the bearing, V pack, bushing, seals, metal rings, inspect wear ring, and hone cylinder.
I) Inspected anti rotation gear and mounting holes for mold.
J) Heater exchange: remove end cap and inspect, new zinc bars.
H) High pressure blow: Inspected and checked valves, seals on valves and hoses.
2024 replaced the outside blow mold cylinder and reduction gear for rotation
2025: Replace seals, O rings and metal rings on main clamp cylinder.
Nissei ASB 70 DPH
Nissei ASB 70 DPH
Serial #259A6339 2003 - 480 Volts - 60 Hz. (made in Japan)
Was in production September 2024
Dryer: Novatec mode IMPC-220 with new: desiccant, filters and heater exchange cleaned and pressure test. Dew point - 40' F', Hopper and take out
Price: $40,000.00 - FOB Gainesville
Start up assistance available
Including the following:
Leveling pads
Spare parts list: barrel heater (2), thermocouple (2)
Air valves: (2), Solid state relays: (6)
Nissei ASB 70 DPH
Serial #259A6350 2003 - 480 Volts - 60 Hz. (made in Japan)
Dryer: Novatec mode IMPC-220 with new: desiccant, filters and heater exchange cleaned and pressure test. Dew point - 40' F', Hopper and take out
Price: $145,000.00 - FOB Gainesville
Start up assistance available
Including the following:
Leveling pads
Spare parts list: barrel heater (2), thermocouple (2)
Air valves: (2), Solid state relays: (6)
Certification List: Annual Maintenance
A) New hydraulic cylinders (2) V90
B) New Injection Cushing cylinders (4) AV50
C) Replace all O rings on hydraulic valves and filters
D) Flush hydraulic tank, clean magnets and filters
E) Toshiba motor: clean, inspect, replace bearings and bake windings, and tested
F) New pump cartridges, original Tokimec, replace pump bearings and seals
G) Blow mold cylinders: replace seals and bolts
H) New Bottom mold cylinders and bolts
I) Heater exchange: clean, dip, pressure test, new zinc bars (4) and gaskets
J) New air cylinder: blow core, stretch, heat pot, heat core, slide plate and eject.
K) New Hydraulic hoses: Yates brand
L) Inspect high pressure air valves and check valves.
M) Injection mold main clamp unit cylinder: replace metal rings and seals
N) Inspection unit IU-35: inspect wear ring, replace bearing, V pack, bushing, seals and metal rings. Inspect barrel heater electric wire connectors
O) New paint inside and outside
N) Replace bad Plexiglas on safety cage with 1/4"
